![]() Immersion mode (designation in the miner status in the form of a snowflake, while it also shows the turnover if someone's fans are not filmed in a slurry).ġ0) Corrections of spelling errors and meanings in the web interface).ġ1) Put in order the descriptions of the profiles with the approximate consumption of AB-OFF / AB-ON and the output of information on overclocking or downvolt.ġ2) Added 4 new profiles for 18.5, 19, 19.5, 20th. The counter is reset after the entire reboot or power-off).Ħ) The tuning log has been redesigned, the maximum number of lines is 20, if more than 20 the oldest records are deleted.Ĩ) The function of exporting the configuration in a multiplier has been added (for reproduction of overclocking, down-volt, applying a profile via BTC Tools).Ĩ) Added new profile, frequency 700 voltage 8.6 (14.7th)ĩ) Added monitoring integration Anthill.farm (see the monitoring section).ġ0) Refinement, operation of fans and temperature sensors.ġ1) Refinement virus detection, and exclusion of infection in Version 3.7.6ġ2) Fixed error displaying online voltage in the absence of boards.3) The function of keeping the temperature on the chips (in case of strong temperature drops and freezing of the ASIC).Ĥ) Modification of the multiplier config (it became possible when transferring the config):ī) Leave the blade and voltage settings unchanged.ĭ) Massively transfer the function of troubleshooting DevFee connection problems.į) Bulk transfer of temperature hold settings.ĥ) Added a quiet fan mode when starting the miner (at your own peril and risk).Ħ) We made a conclusion of information about dead fans in our own log.ħ) Fixed bugs when using Nicehash and improved #xnsub.Ĩ) We did a fan check and added a 500-800 rpm limit (a situation when the rear fan is dead, but rotates due to the flow from the front at the minimum speed).ĩ) Redesigned the output of information when turned on. Immersion mode (designation in the miner status in the form of a snowflake, while it also shows the turnover if someone's fans are not filmed in a slurry).ġ0) Corrections of spelling errors and meanings in the web interface).ġ1) Put in order the descriptions of the profiles with the approximate consumption of AB-OFF / AB-ON and the output of information on overclocking or downvolt.ġ2) Added 4 new profiles for 18.5, 19, 19.5, 20th.Ĥ) Added #xnsub (this is how you add as example :3333#xnsub).ĥ) Added the ability to set a reboot restriction with by trigger when say a blade got disconnected (You can set the maximum number of reboots. For this article, I’ll go over getting the miner set up without using this. It’s basically a project all on it’s own. I bought and used this for my rig because I thought it looked cool, and I liked that I got to assemble it myself. Cgminer 3.8.5 download install#3) The function of keeping the temperature on the chips (in case of strong temperature drops and freezing of the ASIC).Ĥ) Modification of the multiplier config (it became possible when transferring the config):ī) Leave the blade and voltage settings unchanged.ĭ) Massively transfer the function of troubleshooting DevFee connection problems.į) Bulk transfer of temperature hold settings.ĥ) Added a quiet fan mode when starting the miner (at your own peril and risk).Ħ) We made a conclusion of information about dead fans in our own log.ħ) Fixed bugs when using Nicehash and improved #xnsub.Ĩ) We did a fan check and added a 500-800 rpm limit (a situation when the rear fan is dead, but rotates due to the flow from the front at the minimum speed).ĩ) Redesigned the output of information when turned on. Step 2 (Optional) Build the Adafruit 16×2 LCD Plate Assemble and install the Adafruit 16×2 LCD Plate. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |